Technical Advice

Setting Up an AudioCodes MP1xx FXS With Asterisk

This will be the last in the AudioCodes setup series. A quick and dirty configuration for a vanilla Asterisk setup. AudioCodes uses the network address 10.1.10.10 for FXS and 10.1.10.11 for FXO gateways. Setup your network accordingly to access the default address.

Asterisk Setup:

The Asterisk setup is easy. Just create standard type=friend extensions for as many phone extensions as you would like to create in sip.conf. A typical basic entry would look like below.

[1001]
type=friend
context=local ; Context for incoming calls for this user
host=dynamic ; This peer register with us
dtmfmode=inband ; Choices are inband, rfc2833, or info
username=1001
secret=1234
disallow=all
allow=ulaw ; dtmfmode=inband only works with ulaw or alaw!
;progressinband=no ; Polycom phones don’t work properly with “never”

Create dialplan entries in extensions.conf
exten => 1001,1,Dial(SIP/1001|25)

AudioCodes Setup:

Connect the gateway to a network switch and connect a computer to the same
switch. Then configure the IP address of the computer to 10.1.10.XXX (anything but 10 or 11). Then run your web browser and point it to http://10.1.10.10 and login using

Default IP address: 10.1.10.10
Default username: Admin
Default password: Admin

Click -> “Quick Setup” and change the following:

IP Address => IP address of the AudioCodes 124
Subnet Mask => Set to the correct netmask for your local network
Default Gateway Address => Gateway IP address for your LAN
Working With Proxy => Yes
Proxy IP Address => IP address of the Asterisk server
Enable Registration => Set to “Enable”

Restart the gateway and log back in using the new IP address.

Protocol Management -> Protocol Definition -> Proxy & Registration
Registrar IP Address => Set to the IP address of the Asterisk server
Registration Time => 60
Subscription Mode => Per Endpoint
Authentication Mode => Per Endpoint

Go to Protocol Management -> Protocol Definition -> DTMF & Dialing
Max Digits In Phone Num -> Make it a large number like 32 digits

Go to Protocol Management -> Protocol Definition -> Coders
Add coders as needed You need to set at least G.711U-law

Go to Protocol Management -> Endpoint Settings -> Authentication
Set SIP username and password for each port to match your settings in sip.conf

Go to Protocol Management -> Endpoint Phone Numbers
Enter an extension (phone) number for every used channel to match entries in sip.conf

AudioCodes FXS gateway is ready. Worked here YMMV.

Garrett Smith

Garrett is the former VoIP Supply CMO.

View Comments

  • hello

    i have to audio code ip address

    can u suggest me how the configuration is possible with asterisk so that i can monitor/record call

    regard

    chetan

  • Hi Kevin , i configure my audio codec whit a IP public (190.12. XXX . XXX) , but I try connect for web but show me a error

    Unauthorized
    Correct authorization is required for this area. Either your browser does not perform authorization, or your authorization has failed. RomPager server by Digest Access Authentication, which is not supported by your browser.

    Return to last page

  • does not work. I can not get the thing to got ext 9000 to port 1 9001 port2. The only way it works is set to ascending and of course that will not work. the docs for this unit sucks. I am sure it will work nicely if I could get it to work right. the whole point of getting this was to have it work with 2 fax machines and two modems. if it is randomly picking ports then it is useless.

  • Hello. I have the MP-124 FXS model and i'm getting One Way Audio problems

    Do you know anything about that?

Share
Published by
Garrett Smith

Recent Posts

How to Prepare Your VoIP Systems for 2025

Remember Back to the Future II? I loved that movie because they traveled into the…

2 days ago

SIP Chats: Sharath Abraham of Jabra – Panacast 50, BYOD Solutions, and More!

https://youtu.be/qsNO-fZdY3U?si=1A2biOpTwvHG-wiB In the latest episode of SIP Chats, host Brian Hyrek sits down with Sharath…

3 days ago

Watch Now: 2024 November VoIP News Update

https://youtu.be/a--L6ZF9iAw VoIP Supply’s November VoIP News Update: Exciting New Tools, Upcoming Releases, and Giving Back…

7 days ago

Q&A: Wi-Fi 6 vs. Wi-Fi 5: What’s the Real Difference for Everyday Users?

Wireless internet? I remember sharing computer time with my siblings to wait 10 minutes for…

1 week ago

Fanvil FCMS Smart Proporty Solutions Webinar | November 2024

https://youtu.be/0Oxom_f47EE If you missed this webinar, then don't worry, the recording has arrived! This webinar…

2 weeks ago

How To: Extend Your DECT Range for Wireless VoIP Phones – Tips for Large Office Spaces

Ensuring seamless VoIP connectivity across vast areas can be challenging if you're managing a large…

2 weeks ago